Introduction to Metro Ethernet (2024)

Lesson Contents

Ethernet was originally created for the LAN (Local Area Network) and not for the WAN (Wide Area Network), one of the reasons was the distance limitation that the first Ethernet standards offered.

The technology of Ethernet is used a lot in networking products, which makes it cheap to produce Ethernet products compared to other networking technology. This is one of the reasons why Ethernet is interesting to use outside of the LAN.

Metro Ethernet was first used outside of the LAN in metropolitan areas, called MANs (Metropolitan Area Network). We use fiber cabling because of the support for longer distances. Here are some of the standards that are suitable for Metro Ethernet:

NameDistanceBandwidth
100Base-LX1010 Km100 Mbps
1000Base-LX5 Km1 Gbps
1000Base-LX1010 Km1 Gbps
1000Base-ZX100 Km1 Gbps
10Gbase-LR10 Km10 Gbps
10Gbase-ER40 Km10 Gbps
40Gbase-LR410 Km40 Gbps
100Gbase-ER440 Km100 Gbps

As you can see in the table above, we can now cover distances of up to 100 Km (62 miles) and up to 100 Gbps.

Metro Ethernet was first only used in metropolitan areas, that’s why it’s called “Metro” Ethernet. Nowadays it’s also used for long-distance WAN links, often namedCarrier Ethernet.

From the customer’s perspective, it’s like you are connected to a regular switch:

Introduction to Metro Ethernet (1)

On the customer’s side, you get an Ethernet connection that you can connect to your router, switch or firewall. The provider will use switches on the edge of their network. The technology thatis used inside the provider network is unknown to the customer. This could be something like MPLS. Ethernet frames that are sent by the customer router on one end, will be transparently transported to the other end.

Metro Ethernet Services and Topologies

There are several different Metro Ethernetservices, each service has a different topology. The MEF (Metro Ethernet Forum) is a non-profit consortium that defines standards and services for Metro Ethernet. In the remaining of this lesson, we’ll discuss some of the most common services:

  • E-Line (Ethernet Line Service)
  • E-LAN (Ethernet LAN Service)
  • E-Tree (Ethernet Tree Service)

E-Line (Ethernet Line Service)

The Ethernet Line Service is the simplest Metro Ethernet service, it’s a point-to-point connection between two sites:

Introduction to Metro Ethernet (2)

From the customer’s perspective, it’s like connecting two routers to each other with a crossover cable. It’s a layer two link so if you configure IP addresses, the routers will be in the same subnet. The point-to-point link is called an EVC (Ethernet Virtual Circuit).

If you have multiple sites, it is possible to use multiple E-lines on a single physical interface:

Introduction to Metro Ethernet (3)

When you use multiple E-lines on a single physical interface, we use 802.1Q trunking and a different VLAN for each E-line.

In my examples I’m showing routers as the customer devices but since we use Ethernet, you could also use switches.

Another common name for E-Line is VPWS (Virtual Private Wire Service). This name is used when the provider uses MPLS on their network, transporting Ethernet over the MPLS network.

E-LAN (Ethernet LAN Service)

If you have a lot of sites and you want each site to be able to send frames directly to any other site, you might want to use an E-LAN. It’s a full-mesh topology that acts like a big switch:

Introduction to Metro Ethernet (4)

The green line represents a single EVC that connects all four sites together, creating one E-LAN. All sites will be able to reach each other directly.

Another common name for E-LAN is VPLS (Virtual Private LAN Service).

E-Tree (Ethernet Tree Service)

The third topology is the E-Tree, this topology is useful if you have a central site and some other sites that mostly need to access resources at the central site:

Introduction to Metro Ethernet (5)

This is a root with leaves topology where CE1 is theroot of the tree and CE2/CE3 are leaves. It’s also known as a hub and spoke topology, partial mesh or point-to-multipoint. Leave-to-leave communication is still possible but it will have to go through the main site.

Conclusion

You have now learned the basics of Metro Ethernet:

  • Ethernet technology is interesting because it is used in so many products, making it cheaper compared to some other technologies.
  • Ethernet was first used outside of the LAN in MANs (Metropolitan Area Network), which is why we call it Metro Ethernet.
  • Ethernet is also used on WAN connections, which is why we also call it carrier Ethernet. The provider might use another technology on their network but the end-to-end protocol in use is Ethernet.
  • The MEF (Metro Ethernet Forum) defines standards and services for Metro Ethernet.
  • Some basic topologies:
    • E-Line: point-to-point connection between two sites.
    • E-Lan: full-mesh network between different sites.
    • E-Tree: root and leaves topology where the central site is the root of the tree and the other sites are the leaves.
Introduction to Metro Ethernet (2024)
Top Articles
Latest Posts
Article information

Author: Terrell Hackett

Last Updated:

Views: 6209

Rating: 4.1 / 5 (52 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Terrell Hackett

Birthday: 1992-03-17

Address: Suite 453 459 Gibson Squares, East Adriane, AK 71925-5692

Phone: +21811810803470

Job: Chief Representative

Hobby: Board games, Rock climbing, Ghost hunting, Origami, Kabaddi, Mushroom hunting, Gaming

Introduction: My name is Terrell Hackett, I am a gleaming, brainy, courageous, helpful, healthy, cooperative, graceful person who loves writing and wants to share my knowledge and understanding with you.